Hebei Haoaixi Steel Fiber Co., Ltd.
+86-15633600939
Contact Us
  • Phone: +86-15633600939
  • Wechat/WhatsApp: +86-13832557122
  • Email:jun@steelfiberconcretes.com
  • Add: Yangjiatao Industrial Park, Yutian County, Tangshan City, Hebei Province, China

Three characteristics of steel fiber

Dec 10, 2021

1. Adhesion

Since the interface bond between the steel fiber and the concrete matrix is mainly physical, that is, the transmission of frictional shear force is the main factor, so for the steel fiber itself, its bonding performance should be improved from the two aspects of fiber surface and fiber shape. . There are the following four specific methods.

a. Roughen the surface of the steel fiber and make the cross-section irregular. This goal can be achieved by using the melting and extraction method. When the steel fiber is rapidly cooled in the air, the surface shrinks unevenly and becomes rough, and the cross section also shrinks into a crescent shape, increasing the contact area with the substrate. Milled steel fibers have a smooth surface on one side and a rough surface on the other, which also increases the contact area with the concrete.

b. The fibers are plastically processed at a certain distance along the axis of the steel fiber. For example, the "Xinke" steel fiber of Japan's Kobe Steel Corporation's "XOREX" steel fiber of Leibang Corporation of the United States (Figure 2-1, c) and the "S-2" and "S--3" steel fibers of Qing'an Iron and Steel Plant steel fiber. Since the surface is pressed into a prismatic shape, or pressed into a wave shape, the mechanical bonding force is increased.

c. Shape the ends of the steel fibers. Such as ingot milling steel fibers with anchoring platforms at both ends; American Becker Gongdian "DRAM IX" steel fibers (Figure 2-1, e) and Qing'an Iron and Steel Plant "S-4' and as-so steel fibers,. They are made of hooks at both ends; there are also large-head-shaped steel fibers extracted by melting and extraction. Due to the anchoring effect at both ends, the pull-out resistance is improved.

d. Coat the surface of steel fiber with epoxy resin and surface micro-rust treatment. This method does not improve the interfacial bond strength as much as the previous methods, but it also has a certain enhancement effect.

The tests of Ichifu Kobayashi, the University of Liege in Belgium, and Zhang Wengang have all proved that the reinforcing effect of steel fibers with hooks is about double that of straight steel fibers. Hook of steel fiber. These special-shaped steel fibers not only improve the strength of the steel fibers, but also improve the toughness. Although the corrugated steel fiber has little effect on improving the strength of steel fiber reinforced concrete, it can double the toughness.

2. Hardness

No matter which processing method is used, the steel fiber will encounter high heat and rapid cooling during the processing, which is equivalent to the quenching state. Therefore, the surface hardness of steel fibers is higher. Bending rarely occurs during mixing for concrete reinforcement. If the steel fiber is too hard and too brittle, it will be easily broken during stirring, which will affect the reinforcement effect. When the steel fiber is produced by the melting and pumping method, the steel fiber centrifugally ejected from the melting and pumping wheel is still in a high temperature state, and must be dispersed and cooled by a roller or a vibration conveying method. Otherwise, the steel fibers will gather, and the heat will be difficult to dissipate, which will instead play the role of annealing.

3. Corrosion resistance

The introduction of the corrosion resistance test of steel fiber reinforced concrete shows that the cracked steel fiber reinforced concrete components in a humid environment, the concrete at the crack is carbonized, the steel fiber in the carbonized area is corroded, and the carbonization depth and corrosion degree develop with time. For concrete, it mainly uses the post-crack radian and post-crack toughness. Although the crack width is smaller than that of reinforced concrete, there are cracks after all. Therefore, anti-corrosion measures should be taken for steel fiber reinforced concrete used in a humid environment, especially in the seaside. Measures. The face test proves that, on the premise of ensuring that the steel fiber reinforced concrete members have the same bearing capacity, the use of steel fibers with larger diameters can improve corrosion resistance, and the use of epoxy resin-coated or galvanized steel fibers will improve corrosion resistance. If the construction technology permits, this steel fiber can be used only on the surface of the concrete 1-2cm, and non-induced steel fiber can also be used if necessary.